Synfocom Systems LLP

CAT6 UTP Cable supports Gigabit Ethernet (1000 Base-T) standard. Operates at a bandwidth up to 250 Mhz.  This cable well exceeds the requirements of TIA/EIA-568.C.2 Category 6 ISO/IEC Class E

• Comply with Cat6 specifications
• 4-pair unshielded twisted pair (UTP) cable
• Pairs are braided in aluminum foil with drain wire
• 23 AWG solid copper conductor for superior conductivity
• HDPE insulation
• FR PVC Jacket
• Verified compliant with EIA/TIA standards by ETL
• UL-listed
• Packaged in an easy-to-pull box for easier installation
• 100% Copper and no mix of other material
• The speed of a wired LAN is largely determined by how fast data is transmitted between computers and network components.
• The solid construction of the Technotech Cat6 cable helps you stream video, music, transmit data at higher speeds by providing a fast and reliable connection.
• Note: A network's speed is determined by many factors in addition to the cables, including your router, switch boxes, and component.

• Faster AC Wi-Fi—AC1200 dual-band is ideal for 4K video streaming and high-speed downloading.
• Far-Reaching Coverage—4× antennas and Beamforming delivers extensive Wi-Fi coverage and reliable connections.
• Multi-Mode 3-in-1—Supports Router, Access Point, and Range Extender modes for added flexibility.
• Parental Controls—Manages when and how connected devices can access the internet.
• Guest Network—Provides separate access for guests in order to secure the host network.
• Smooth HD Streaming—Supports IGMP Proxy/Snooping, Bridge, and Tag VLAN to optimize IPTV streaming.
• IPv6 Supported—Compatible with the IPv6 (the latest Internet Protocol version 6).
• Compact and Mountable—Designed to conserve space and complement any décor

CAT6 UTP Cable supports Gigabit Ethernet (1000 Base-T) standard. Operates at a bandwidth up to 250 Mhz.  This cable well exceeds the requirements of TIA/EIA-568.C.2 Category 6 ISO/IEC Class E

• 4-pair unshielded twisted pair (UTP) cable
• Pairs are braided in aluminum foil with drain wire
• 23 AWG solid copper conductor for superior conductivity
• HDPE insulation
• FR PVC Jacket
• Verified compliant with EIA/TIA standards by ETL
• UL-listed
• Packaged in an easy-to-pull box for easier installation

This Category 6, four pair cable is a high-speed, high performance, 100 ohm impedance cable capable of carrying high bit-rate signaling for extended distances in horizontal cabling. Signal amplifiers are not required for a length of 328 feet (100 M). Applications can include Voice, ISDN, ATM 155 Mbps, ATM 622 Mbps 100 Mbps TPDDI, Fast and Giga Ethernet, and IEEE 802.3/5/12, 100 BASE VG (100 BASE NE), 100 BASE-T, 100 Mbps TP-PMD, 1000 BASE-T, 10Gb and any other future applications designed for Category 6 Cables

• For Data Center Applications
• High bandwidth @ 250 MHz
• 4 Pair 23 AWG
• LSZH jacket
• High speed transmission of Voice, Video and Data on LAN
• Complies to ANSI/TIA-568-C.2, ISO/IEC 11801 Class E, ISO/IEC 60332-1

Our firm is a leading name, involved in presenting Armored Fiber Optic Cable. This series is enormously employed by clientele owing to their top features.

Features:

• Sturdy structure

• Longer life

• Affordable cost

• Durable finish

• Low maintenance

1F-G657A1 Fibre, 2.5MM OD FLAT FTTH WITH 3 STEEL WIRE+ CONNECTORS 50 Meters
The fiber optic drop cable patch cord has two connectors at each end of the cable to make a connection; a pigtail cable is one cable with a connector. The connectors are with SC type,  A SM convertion patch cord is with two different connectors. 
FTTH Optical fiber patch cord is made up by optical communication unit, strengthen pieces and the sheath composition, that is put the optical communication unit in the middle, both sides parallel place two roots non-metallic strengthen members or metal strengthening component phosphate steel wire, finally squeeze the black or color sheath into cable

• High tensile metal reinforcement with 3 steel wire strength
• SC/APC to SC/APC Single Mode simplex Drop cable patch cord 
• Insertion loss: ≤ 0.3 dB Return loss: ≥ 50 dB
• Special fiber resistance to bending, provide greater bandwidth

dr.com connectors include RJ 45 Connector plug primarily used for network cabling and it is usually used for data transmission. SC, LC, ST, FC adapters that have compact design & high precision.
Modular Plug category 5e/Class D, a-position, a-wire, UTP(unshielded) shall terminate most 4-pair, 24-26AWG, lO0ohm, solid orstranded, unshielded twisted pair cable.T56aA and T56aB wiring schemes are all compliant

•  RJ45 modular plug with 8P8C
•  Meet wiring scheme T568A/T568B
•  3 Prong Design with Gold Plating
•  750 Mating Cycle
•  Pack of 100 Plugs

1F-G657A1 Fibre, 2.5MM OD FLAT FTTH WITH 3 STEEL WIRE+ CONNECTORS 70 Meters
The fiber optic drop cable patch cord has two connectors at each end of the cable to make a connection; a pigtail cable is one cable with a connector. The connectors are with SC type,  A SM convertion patch cord is with two different connectors. 
FTTH Optical fiber patch cord is made up by optical communication unit, strengthen pieces and the sheath composition, that is put the optical communication unit in the middle, both sides parallel place two roots non-metallic strengthen members or metal strengthening component phosphate steel wire, finally squeeze the black or color sheath into cable

• High tensile metal reinforcement with 3 steel wire strength
• SC/APC to SC/APC Single Mode simplex Drop cable patch cord 
• Insertion loss: ≤ 0.3 dB Return loss: ≥ 50 dB
• Special fiber resistance to bending, provide greater bandwidth

Ratio Couplers are an all fiber, polished directional coupler with variable coupling ratio. These devices can be used to divide or combine optical signals in fiber optics research. Available wavelengths include 630 nm, 830 nm, 980 nm, 1060 nm, 1300 nm, and 1550 nm.

• Very precise coupling ratio adjustment — from 0–100%
• Low insertion loss
• High polarization isolation
• PM and non-PM types available

Ratio Couplers are an all fiber, polished directional coupler with variable coupling ratio. These devices can be used to divide or combine optical signals in fiber optics research. Available wavelengths include 630 nm, 830 nm, 980 nm, 1060 nm, 1300 nm, and 1550 nm.

• Very precise coupling ratio adjustment — from 0–100%
• Low insertion loss
• High polarization isolation
• PM and non-PM types available

Ratio Couplers are an all fiber, polished directional coupler with variable coupling ratio. These devices can be used to divide or combine optical signals in fiber optics research. Available wavelengths include 630 nm, 830 nm, 980 nm, 1060 nm, 1300 nm, and 1550 nm.

• Very precise coupling ratio adjustment — from 0–100%
• Low insertion loss
• High polarization isolation
• PM and non-PM types available

Ratio Couplers are an all fiber, polished directional coupler with variable coupling ratio. These devices can be used to divide or combine optical signals in fiber optics research. Available wavelengths include 630 nm, 830 nm, 980 nm, 1060 nm, 1300 nm, and 1550 nm.

• Very precise coupling ratio adjustment — from 0–100%
• Low insertion loss
• High polarization isolation
• PM and non-PM types available

Ratio Couplers are an all fiber, polished directional coupler with variable coupling ratio. These devices can be used to divide or combine optical signals in fiber optics research. Available wavelengths include 630 nm, 830 nm, 980 nm, 1060 nm, 1300 nm, and 1550 nm.

• Very precise coupling ratio adjustment — from 0–100%
• Low insertion loss
• High polarization isolation
• PM and non-PM types available

Ratio Couplers are an all fiber, polished directional coupler with variable coupling ratio. These devices can be used to divide or combine optical signals in fiber optics research. Available wavelengths include 630 nm, 830 nm, 980 nm, 1060 nm, 1300 nm, and 1550 nm.

• Very precise coupling ratio adjustment — from 0–100%
• Low insertion loss
• High polarization isolation
• PM and non-PM types available

Ratio Couplers are an all fiber, polished directional coupler with variable coupling ratio. These devices can be used to divide or combine optical signals in fiber optics research. Available wavelengths include 630 nm, 830 nm, 980 nm, 1060 nm, 1300 nm, and 1550 nm.

• Very precise coupling ratio adjustment — from 0–100%
• Low insertion loss
• High polarization isolation
• PM and non-PM types available

4 Way PLC Tube Type Planar Light Circuit (PLC) splitters exhibit uniform signal splitting for FTTH and PON networks. It is fabricated using silica optical waveguide technology,

• 4 way PLC Tube
• Without Connector
• Quartz substrate integrated waveguard
• Good Uniformity and low insertion loss
• Low Polaration Dependent Loss
• Excellent Environmental Stability
• High Reliability
• channel-to-channel uniformity
• Small size

8 Way PLC Tube Type Planar Light Circuit (PLC) splitters exhibit uniform signal splitting for FTTH and PON networks. It is fabricated using silica optical waveguide technology,

• 8 way PLC Tube
• Without Connector
• Quartz substrate integrated waveguard
• Good Uniformity and low insertion loss
• Low Polaration Dependent Loss
• Excellent Environmental Stability
• High Reliability
• channel-to-channel uniformity
• Small size

4 Way PLC Plug-In Type (Cassette Type) SC/UPC is a Planar lightwave circuit (PLC) splitter is a type of optical power management device that is fabricated using silica optical waveguide technology. It features a small size, high reliability, wide operating wavelength range, and good channel-to-channel uniformity, and is widely used in PON networks to realize optical signal power splitting. We provide the whole series of 4,8,16 PLUG-IN TYPE products that are tailored for a specific application

• Low Insertion Loss.
• Low PDL.
• High Return Loss.
• Uniform Power Splitting

8 Way PLC Plug-In Type (Cassette Type) SC/UPC is a Planar lightwave circuit (PLC) splitter is a type of optical power management device that is fabricated using silica optical waveguide technology. It features a small size, high reliability, wide operating wavelength range, and good channel-to-channel uniformity, and is widely used in PON networks to realize optical signal power splitting. We provide the whole series of 4,8,16 PLUG-IN TYPE products that are tailored for a specific application

• Low Insertion Loss.
• Low PDL.
• High Return Loss.
• Uniform Power Splitting

2 Way Joint Enclosure Box / Tiffin boxes can be used in aerial, direct burial, and duct. The strong housing and main components achieve fire-resistant, waterproof and quakeproof protection of splicing while pulling, tension and impact - it keeps joint enclosure used in the bad natural environment for a long time while guaranteeing the best quality of the product

• High quality plastics are compact and lite weight. Easy to install and long life.
• Designed to be an outdoor usage and 14 splicing tubes can be fixed in this.
• Removable cover for easy access and 100% waterproof
• Applications :Optical Fiber Network,Telecommunications networks,FTTH, FTTx,FTTP,OSP

4 Way Joint Enclosure Box / Tiffin boxes can be used in aerial, direct burial, and duct. The strong housing and main components achieve fire-resistant, waterproof and quakeproof protection of splicing while pulling, tension and impact - it keeps joint enclosure used in the bad natural environment for a long time while guaranteeing the best quality of the product

• High-quality plastics are compact and lite weight. Easy to install and long life.
• Designed to be an outdoor usage and 14 splicing tubes can be fixed in this.
• Removable cover for easy access and 100% waterproof
• Applications :Optical Fiber Network,Telecommunications networks,FTTH, FTTx,FTTP,OSP

8 Way PLC Tube Type Planar Light Circuit (PLC) splitters exhibit uniform signal splitting for FTTH and PON networks. It is fabricated using silica optical waveguide technology,

• 8 way PLC Tube
• Without Connector
• Quartz substrate integrated waveguard
• Good Uniformity and low insertion loss
• Low Polaration Dependent Loss
• Excellent Environmental Stability
• High Reliability
• channel-to-channel uniformity
• Small size

LC/APC-LC/APC Single mode Simplex G657A1 Optical patch cord (LSZH) -5meters
Fiber optic patch cords and pigtails provide interconnect and cross-connect of applications over installations in entrance installations in entrance facilities, telecommunications rooms, data centers and at the desk. Patch cords support network applications in main, horizontal and equipment distribution areas and are available in riser (OFNR), and low smoke zero halogen (LSZH) rated jacket materials to comply with local cabling ordinances. Pre-terminated fiber optic pigtails support fusion splice field termination applications. Fiber optic patch cords and pigtails are available in OM4, OM3, OM2, OM1, or OS1/ OS2 fiber types to meet the demands of Gigabit Ethernet, 10 Gigabit Ethernet and high speed Fibre Channel.

• High quality zirconia ferrules
• PC radius ferrule tip
• 100% insertion loss
• Low mated pair insertion loss
• High quality nickel-plated die-cast ST nut
• Precision engineered plastic SC housings
• Wide temperature operating range
• UL-VO flammability rating on polymer materials

LC/UPC-LC/UPC Single mode Simplex G657A1 Optical patch cord (LSZH) -5meters
Fiber optic patch cords and pigtails provide interconnect and cross-connect of applications over installations in entrance installations in entrance facilities, telecommunications rooms, data centers and at the desk. Patch cords support network applications in main, horizontal and equipment distribution areas and are available in riser (OFNR), and low smoke zero halogen (LSZH) rated jacket materials to comply with local cabling ordinances. Pre-terminated fiber optic pigtails support fusion splice field termination applications. Fiber optic patch cords and pigtails are available in OM4, OM3, OM2, OM1, or OS1/ OS2 fiber types to meet the demands of Gigabit Ethernet, 10 Gigabit Ethernet and high speed Fibre Channel.

• High quality zirconia ferrules
• PC radius ferrule tip
• 100% insertion loss
• Low mated pair insertion loss
• High quality nickel-plated die-cast ST nut
• Precision engineered plastic SC housings
• Wide temperature operating range
• UL-VO flammability rating on polymer materials

2 Way PLC Tube Type Planar Light Circuit (PLC) splitters exhibit uniform signal splitting for FTTH and PON networks. It is fabricated using silica optical waveguide technology,

• 2 way PLC Tube
• Without Connector
• Quartz substrate integrated waveguard
• Good Uniformity and low insertion loss
• Low Polaration Dependent Loss
• Excellent Environmental Stability
• High Reliability
• channel-to-channel uniformity
• Small size

2 Way PLC Tube Type Planar Light Circuit (PLC) splitters exhibit uniform signal splitting for FTTH and PON networks. It is fabricated using silica optical waveguide technology,

• 2 way PLC Tube
• Without Connector
• Quartz substrate integrated waveguard
• Good Uniformity and low insertion loss
• Low Polaration Dependent Loss
• Excellent Environmental Stability
• High Reliability
• channel-to-channel uniformity
• Small size

BC-315A VFL visual fault locator is a visible red laser designed to inject visible light energy into a fiber. Sharp bends, breaks, faulty connectors, and other faults will “leak” red light allowing technicians to visually spot the defects. The VFI is an ideal tool for locating a large number of defects that occur at connection points in and around fiber cabinets which are hidden in an OTDRs “blind-spot” or dead-zone. AFL offers VFI units for both single-ferrule and multi-ferrule connector styles

• Fiber identification
• Power output:20mW
• Fiber continuity testing
• Connection polarity testing
• Precise optical fault location
• Cable route location

BC-315A VFL visual fault locator is a visible red laser designed to inject visible light energy into a fiber. Sharp bends, breaks, faulty connectors, and other faults will “leak” red light allowing technicians to visually spot the defects. The VFI is an ideal tool for locating a large number of defects that occur at connection points in and around fiber cabinets which are hidden in an OTDRs “blind-spot” or dead-zone. AFL offers VFI units for both single-ferrule and multi-ferrule connector styles

• Fiber identification
• Power output:10mW
• Fiber continuity testing
• Connection polarity testing
• Precise optical fault location
• Cable route location

BC-315A VFL visual fault locator is a visible red laser designed to inject visible light energy into a fiber. Sharp bends, breaks, faulty connectors, and other faults will “leak” red light allowing technicians to visually spot the defects. The VFI is an ideal tool for locating a large number of defects that occur at connection points in and around fiber cabinets which are hidden in an OTDRs “blind-spot” or dead-zone. AFL offers VFI units for both single-ferrule and multi-ferrule connector styles

• Fiber identification
• Power output:30mW
• Fiber continuity testing
• Connection polarity testing
• Precise optical fault location
• Cable route location

4 Port OLT L3 series EPON OLT products are 1U height 19-inch rack mount products. The features of the OLT are small, convenient, flexible, easy to deploy, high performance. It is appropriate to be deployed in compact room environment. The OLTs can be used for “Triple-Play”, VPN, IP Camera, Enterprise LAN and ICT applications. Supports Networking Features like VLAN Trunk, PortProtection, MAC Binding, Port Limit, Queue Control, Loop Detection, QinQ VLAN, Storm Control, Link Aggregation

• 4GE(copper) and 4SFP slots
• Independent interface for uplink
• 4x EPON OLT ports for downstream
• support 256 ONUs under 1:64 splitter ratio
• Supports CLI, Telnet, Web, SNMP, and RMON
• STP / RSTP /MSTP

8 Port OLT L3 series EPON OLT products are 1U height 19-inch rack mount products. The features of the OLT are small, convenient, flexible, easy to deploy, high performance. It is appropriate to be deployed in compact room environment. The OLTs can be used for “Triple-Play”, VPN, IP Camera, Enterprise LAN, and ICT applications. Supports Networking Features like VLAN Trunk, PortProtection, MAC Binding, Port Limit, Queue Control, Loop Detection, QinQ VLAN, Storm Control, Link Aggregation

• 8GE(copper) and 8SFP slots
• Independent interface for uplink
• 8x EPON OLT ports for downstream
• Support 512ONUs under 1:64 splitter ratio
• Supports CLI, Telnet, Web, SNMP, and RMON
• STP / RSTP /MSTP

DBC 8 Pon Port GPON OLT is a 1U height 19-inch rack-mountable product. The features of the OLT are small, convenient, flexible, easy to deploy, high performance. It is appropriate to be deployed in compact room environment. The OLT can be used for “Triple-Play”, VPN, IP Camera, Enterprise LAN, and ICT applications.Supports Networking Features like VLAN Trunk, PortProtection, MAC Binding, Port Limit, Queue Control, Loop Detection, QinQ VLAN, Storm Control, Link Aggregation

• 8GE(copper) and 8SFP(6*1GE+2*10GE) slots independent interface for uplink
• 8*GPON OLT ports for downstream
• Support 1024 ONUs under 1:128 splitter ratio
• Dual (SMPS) Power Supply 
• Supports CLI, Telnet, Web, SNMP, and RMON
• STP / RSTP /MSTP

DBC 4 Pon Port GPON OLT is a 1U height 19 inch rack mountable product. The features of the OLT are small, convenient, flexible, easy to deploy, high performance. It is appropriate to be deployed in compact room environment. The OLT can be used for “Triple-Play”, VPN, IP Camera, Enterprise LAN and ICT applications.

• DBC 4 Pon Port GPON OLT provides 4GE(copper)
• 2 *GE (SFP) / 10GE (SFP+) slots independent interface for uplink, and
• 4*GPON OLT ports for downstream.
• It can support 512 ONUs under 1:128 splitter ratio

2GE+1POTS+WiFi GPON/EPON HGU terminal devices are designed for fulfilling FTTH and triple play service demand of fixed network operators. These boxes are based on the mature Chipset (Realtek) technology, which has a high ratio of performance to price, and the technology of IEEE802.11b/g/n/ac WiFi, Layer 2/3, and high-quality VoIP as well. Support full management of HGU devices through DBC OLT. They are highly reliable Product overview and easy to maintain, with guaranteed QoS for different services. And they are fully compliant with technical regulations such as IEEE802.3ah???ITU-T G.984.x and technical requirement of GPON Equipment

• Support full management of HGU functions by DBC OLT
• Plug and play, features auto-detecting, autoconfiguration, and auto firmware upgrade, etc
• Integrated OAM/OMCI remote configuration and maintenance function
• Support rich QinQ VLAN functions and IGMP Snooping multicast features
• Fully compatibility with OLT based on Special Features Broadcom/PMC/Cortina chipset
• Support 802.11n/ac WiFi(4T4R) function
• Support NAT, Firewall function
• Support IPv4 and IPv6 dual-stack
• Support SIP protocol
• Integrated line testing compliant with GR-909 on POTS

96F-G652D Fibre, 12.5mm-OD; ARMOURED MICRO (PLATINUM)
96F-125-PLAT-AR is an Unarmoured, Mulitube, 96Core PLATINUM Cable, with 12.5MM OD,Non metallic, anti- FRP rod as central strength member (CSM). Loose tube containing coloured fibers and filled with thixotropic jelly, Cable core fully filled with flooding jelly. S/Z Core wrapped with polyester tape. Outer sheath with UV Stabilized HDPE compound Fiber count 2F-144F (SM Fiber G.652D, G.655, G.657 and Multimode OM1, OM2, OM3 & OM4)

• Suitable for blowing in ducts
• Suitable for installation alongside power lines
• Local Loop, metro, long-haul and broadband network
• Light Weight and flexible
• Available upto 144 Fibers

48F-G652D Fibre, 11.5mm-OD; ARMOURED MICRO (PLATINUM)
48F-115-PLAT-AR is an Unarmoured, Mulitube, 48Core PLATINUM Cable, with 11.5MM OD,Non metallic, anti- FRP rod as central strength member (CSM). Loose tube containing coloured fibers and filled with thixotropic jelly, Cable core fully filled with flooding jelly. S/Z Core wrapped with polyester tape. Outer sheath with UV Stabilized HDPE compound Fiber count 2F-144F (SM Fiber G.652D, G.655, G.657 and Multimode OM1, OM2, OM3 & OM4)

• Suitable for blowing in ducts
• Suitable for installation alongside power lines
• Local Loop, metro, long-haul and broadband network
• Light Weight and flexible
• Available upto 144 Fibers

72F-G652D Fibre, 11.5mm-OD; ARMOURED MICRO (PLATINUM)
72F-115-PLAT-AR is an Unarmoured, Mulitube, 72 Core PLATINUM Cable, with 11.5MM OD,Non metallic, anti- FRP rod as central strength member (CSM). Loose tube containing coloured fibers and filled with thixotropic jelly, Cable core fully filled with flooding jelly. S/Z Core wrapped with polyester tape. Outer sheath with UV Stabilized HDPE compound Fiber count 2F-144F (SM Fiber G.652D, G.655, G.657 and Multimode OM1, OM2, OM3 & OM4)

• Suitable for blowing in ducts
• Suitable for installation alongside power lines
• Local Loop, metro, long-haul and broadband network
• Light Weight and flexible
• Available upto 144 Fibers

24F-G652D Fibre, 11.5mm-OD; ARMOURED MICRO (PLATINUM)
24F-115-PLAT-AR is an Unarmoured, Mulitube, 24Core PLATINUM Cable, with 11.5MM OD,Non metallic, anti- FRP rod as central strength member (CSM). Loose tube containing coloured fibers and filled with thixotropic jelly, Cable core fully filled with flooding jelly. S/Z Core wrapped with polyester tape. Outer sheath with UV Stabilized HDPE compound Fiber count 2F-144F (SM Fiber G.652D, G.655, G.657 and Multimode OM1, OM2, OM3 & OM4)

• Suitable for blowing in ducts
• Suitable for installation alongside power lines
• Local Loop, metro, long-haul and broadband network
• Light Weight and flexible
• Available upto 144 Fibers

24F-G652D Fibre, 9.5mm-OD; Duct UNARMOURED(GOLD)
24F-95-GOLD-UA is an Unarmoured, Mulitube, 24Core GOLD Cable, with 9.5MM OD,Non metallic, anti- FRP rod as central strength member (CSM). Loose tube containing coloured fibers and filled with thixotropic jelly, Cable core fully filled with flooding jelly. S/Z Core wrapped with polyester tape. Outer sheath with UV Stabilized HDPE compound Fiber count 2F-144F (SM Fiber G.652D, G.655, G.657 and Multimode OM1, OM2, OM3 & OM4)

• Suitable for blowing in ducts
• Suitable for installation alongside power lines
• Local Loop, metro, long-haul and broadband network
• Light Weight and flexible
• Available upto 144 Fibers

2F-G652D Fibre, 5mm OD With 2FRP and YARN (On-request) Unarmoured (Economy)
2F-50-ECO-UA is an Unarmoured, Unitube, 2Core Economy Cable, with 5MM OD & (2)x 1mm FRP, Non-metallic - anti-buckling FRP Rod is Used as strength member embedded in the sheath on both sides for support. A single loose tube filled with thixotropic jelly and centrally placed in the cable. The outer sheath is 100% Virgin Plastic with UV Stabilized HDPE compound  Suitable for duct installation Used for CATV and other networks  Light in weight Small cable diameter Ease of installation

• Suitable for duct installation
• Used for CATV and other networks 
• Light in weight
• Small cable diameter
• Ease of installation

12F-G652D Fibre, 6mm OD With 2FRP and YARN (On-request) Unarmoured (Economy)
12F-60-ECO-UA is an Unarmoured, Unitube, 12Core Economy Cable, with 6MM OD & (2)x 1mm FRP, Non-metallic - anti-buckling FRP Rod is Used as strength member embedded in the sheath on both sides for support. A single loose tube filled with thixotropic jelly and centrally placed in the cable. The outer sheath is 100% Virgin Plastic with UV Stabilized HDPE compound 

• Suitable for duct installation
• Used for CATV and other networks 
• Light in weight
• Small cable diameter
• Ease of installation

2F-G652D Fibre, 5.5mm OD With 2FRP and YARN (On-request) Unarmoured (Economy)
2F-55-ECO-UA is an Unarmoured, Unitube, 2Core Economy Cable, with 5.5MM OD & (2)x 1mm FRP, Non-metallic - anti-buckling FRP Rod is Used as strength member embedded in the sheath on both sides for support. A single loose tube filled with thixotropic jelly and centrally placed in the cable. The outer sheath is 100% Virgin Plastic with UV Stabilized HDPE compound 

• Suitable for duct installation
• Used for CATV and other networks 
• Light in weight
• Small cable diameter
• Ease of installation

6F-G652D Fibre, 5.8mm OD With 2FRP and YARN (On-request) Unarmoured (Economy)
6F-58-ECO-UA is an Unarmoured, Unitube, 6Core Economy Cable, with 5.8MM OD & (2)x 1mm FRP, Non-metallic - anti-buckling FRP Rod is Used as strength member embedded in the sheath on both sides for support. A single loose tube filled with thixotropic jelly and centrally placed in the cable. The outer sheath is 100% Virgin Plastic with UV Stabilized HDPE compound 

• Suitable for duct installation
• Used for CATV and other networks 
• Light in weight
• Small cable diameter
• Ease of installation

24F-G652D Fibre, 8.5mm OD With 2FRP and YARN (On-request) Unarmoured (Economy)
24F-85-GOLD-UA is an Unarmoured, Unitube, 24Core GOLD Cable, with 8.5MM OD & (2)x 1mm FRP, Non-metallic - anti-buckling FRP Rod is Used as strength member embedded in the sheath on both sides for support. A single loose tube filled with thixotropic jelly and centrally placed in the cable. The outer sheath is 100% Virgin Plastic with UV Stabilized HDPE compound 

• Suitable for duct installation
• Used for CATV and other networks 
• Light in weight
• Small cable diameter
• Ease of installation

1F-G652D Fibre, 4mm-OD with YARN(no FRP); ROUND FTTH
Flat drop cable offers ease of installation of standard loose tube cable in an easy access loose tube design. The dielectric element eliminates any grounding requirement.

• 1F per tube - Blue Colour
•  4F per tube - Blue, Orange, Green & Aqua/Natural Or Any Colour
•  PBT Loose Tube Filled With Thixotropic gel
•  Glass fibre roving to meet tensile strength & anti buckling properties GFR (Non Metallic) - 2 Nos - 600 TEX.
•  UV Proof HDPE - Black

2F-G652D Fibre, 4.5MM-OD with 2-FRP & YARN; ROUND FTTH
Flat drop cable offers ease of installation of standard loose tube cable in an easy access loose tube design. The dielectric element eliminates any grounding requirement

• 1F per tube - Blue Colour
•  4F per tube - Blue, Orange, Green & Aqua/Natural Or Any Colour
•  PBT Loose Tube Filled With Thixotropic gel
•  2 FRP x 0.5mm FRP to meet tensile strength & anti buckling properties FRP (Non Metallic) - 2 Nos
•  UV Proof HDPE - Black

CAT 5e UTP 4 Pair 0.40 mm LDPE LAN CABLE

• Conductor Resistance (DC): 153 Ω /Km @200 C. Max.
• Resistance Unbalance: 5 % Max.
• Mutual Capacitance: 5.6 nF/100 mtrs. Max.
• Capacitance Unbalance Pair/Ground: 330PF/100M Max
• Propagation Delay Skew: < 536 nS/100M
• Normal Velocity of Propagation: 69%
• Impedance: 100 ± 15% Ω
• Worst Case cable skew :< 45ns/100m

The pack of 100 Ubiquiti Networks TOUGHCable Connectors is specifically designed for use with Ubiquiti TOUGHCables so you can create Cat 5e cables. The connectors have a shielded design that protects the signal against ESD interference. Furthermore, the connector can be terminated without soldering.

• Category 5e Compliance
• Shielded Design
• ESD Protection
• Designed for Ubiquiti TOUGHCable

D-Link RJ45 connector is a modular plug used primarily for network cabling and it is usually used for data transmission

• RJ45 modular plug supports 4 twisted pairs, 8 positions, 8 connectors of 100pcs/Pack
• Housing: PC, UL94V-2, transparent color
• Contact Terminal: Copper Alloy
• Finished: 03MU micro-inch gold plating
• Operating temperature:-40???C to 80???C
• Use for 24-26 AWG stranded wires, meet wiring scheme T568A/T568B

HGU-V200-4AC is a Dual band WIFI ONT, HGU terminal devices are designed for fulfilling FTTH and triple play service demand of fixed network operators. These boxes are based on the mature Chipset (Realtek) technology, which has a high ratio of performance to price, and the technology of IEEE802.11b/g/n/ac WiFi, Layer 2/3, and high-quality VoIP as well. Support full management of HGU devices through DBC OLT. They are highly reliable Product overview and easy to maintain, with guaranteed QoS for different services. And they are fully compliant with technical regulations such as IEEE802.3ah???ITU-T G.984.x and technical requirement of GPON Equipment

• Support full management of HGU functions by DBC OLT
• Plug and play, features auto-detecting, autoconfiguration, and auto firmware upgrade, etc
• Integrated OAM/OMCI remote configuration and maintenance function
• Support rich QinQ VLAN functions and IGMP Snooping multicast features
• Fully compatibility with OLT based on Special Features Broadcom/PMC/Cortina chipset
• Support 802.11n/ac WiFi(4T4R) function
• Support NAT, Firewall function
• Support IPv4 and IPv6 dual-stack
• Support SIP protocol
• Integrated line testing compliant with GR-909 on POTS

GPON/EPONONT 1GE+1FE+1VOIP+WiFi(xPON) has an Integrated GPON interface, to meet the ITU-T G.984 specification The Dynamic Bandwidth Allocation (DBA) mechanism enables all users to share the maximum 2.5Gbps bandwidth reasonably, guaranteeing a reliable QoS. Full management through an Operation Administration Maintenance (OAM) protocol based on IEEE802.3ah, including configuration, alarm, performance monitoring, fault isolation, and security management, etc. It supports remote management through OLT and local console management as well.

• Supports IGMP multicast, effective use of broadband.
• Supports multicast VLAN.
• Support 802.11n WiFi(2T2R) function
• Support NAT, Firewall function
• Support IPv4 and IPv6 dual-stack
• Integrated line testing compliant with GR-909 on POTS
• Supports FEC and DBA

Ratio Couplers are an all fiber, polished directional coupler with variable coupling ratio. These devices can be used to divide or combine optical signals in fiber optics research. Available wavelengths include 630 nm, 830 nm, 980 nm, 1060 nm, 1300 nm, and 1550 nm.

• Very precise coupling ratio adjustment — from 0–100%
• Low insertion loss
• High polarization isolation
• PM and non-PM types available

Ratio Couplers are an all fiber, polished directional coupler with variable coupling ratio. These devices can be used to divide or combine optical signals in fiber optics research. Available wavelengths include 630 nm, 830 nm, 980 nm, 1060 nm, 1300 nm, and 1550 nm.

• Very precise coupling ratio adjustment — from 0–100%
• Low insertion loss
• High polarization isolation
• PM and non-PM types available

Ratio Couplers are an all fiber, polished directional coupler with variable coupling ratio. These devices can be used to divide or combine optical signals in fiber optics research. Available wavelengths include 630 nm, 830 nm, 980 nm, 1060 nm, 1300 nm, and 1550 nm.

• Very precise coupling ratio adjustment — from 0–100%
• Low insertion loss
• High polarization isolation
• PM and non-PM types available

Ratio Couplers are an all fiber, polished directional coupler with variable coupling ratio. These devices can be used to divide or combine optical signals in fiber optics research. Available wavelengths include 630 nm, 830 nm, 980 nm, 1060 nm, 1300 nm, and 1550 nm.

• Very precise coupling ratio adjustment — from 0–100%
• Low insertion loss
• High polarization isolation
• PM and non-PM types available

Ratio Couplers are an all fiber, polished directional coupler with variable coupling ratio. These devices can be used to divide or combine optical signals in fiber optics research. Available wavelengths include 630 nm, 830 nm, 980 nm, 1060 nm, 1300 nm, and 1550 nm.

• Very precise coupling ratio adjustment — from 0–100%
• Low insertion loss
• High polarization isolation
• PM and non-PM types available

Ratio Couplers are an all fiber, polished directional coupler with variable coupling ratio. These devices can be used to divide or combine optical signals in fiber optics research. Available wavelengths include 630 nm, 830 nm, 980 nm, 1060 nm, 1300 nm, and 1550 nm.

• Very precise coupling ratio adjustment — from 0–100%
• Low insertion loss
• High polarization isolation
• PM and non-PM types available

Ratio Couplers are an all fiber, polished directional coupler with variable coupling ratio. These devices can be used to divide or combine optical signals in fiber optics research. Available wavelengths include 630 nm, 830 nm, 980 nm, 1060 nm, 1300 nm, and 1550 nm.

• Very precise coupling ratio adjustment — from 0–100%
• Low insertion loss
• High polarization isolation
• PM and non-PM types available

Ratio Couplers are an all fiber, polished directional coupler with variable coupling ratio. These devices can be used to divide or combine optical signals in fiber optics research. Available wavelengths include 630 nm, 830 nm, 980 nm, 1060 nm, 1300 nm, and 1550 nm.

• Very precise coupling ratio adjustment — from 0–100%
• Low insertion loss
• High polarization isolation
• PM and non-PM types available

BC342N-PV Mini Optical Power Meter FTTX/BROADBAND installation Fiber & RJ45 comprehensive testing tool OPM/RJ45 Sequence/RJ45 Tracker/Flashlight/VFL

• Wavelength Memory Function
• Automatic Shutdown
• RJ45 Sequence
• RJ45 Tracker
• Support User Calibration
• Recover Factory Settings
• Supporting SC/ST/FC Interface
• Intelligent Power Saving
• Supporting simultaneous linear (mW) & non-linear (dBm) display

EPON SFP transceiver is the family of high performance optical modules providing a symmetric 1.25 Gb/s downstream and 1.25 Gb/s upstream data link over a single fiber using a 1490 nm continuous-mode transmitter and 1310 nm burst-mode receiver. ... GPON SFP OLT transceivers support 1000BASE-PX20-D for 20 km applications

• Connector type : SC
• Simplex Communication
• DFB--LD Laser
• Distance 20km
• Operating temp: 0~70°C

Enhanced performance cable for transmission of high-speed data, digital and analogue voice and video (RGB) signals on LANs. Supports Gigabit Ethernet (100 BaseT) standard. Operates at a bandwidth of 100 MHz. As per the requirements of TIA/EIA-568-C.2

• Solid Bare Electrolytic Grade Copper
• Nominal Conductor Diameter 0.40 ± 0.015 mm
• Polyethylene Insulation
• Outer Jacket: PE
• Black Outer Jacket

The black level 2 Ubiquiti Networks 100' TOUGHCableCARRIER Outdoor Shielded Ethernet Cable is a Category 5e cable that features an integrated ESD drain wire, anti-crosstalk divider, and secondary shielding. It is rated to provide optimal performance on Gigabit Ethernet networks.

• Improves Overall Ethernet Performance
• PE Outdoor-Rated, Weatherproof Jacket
• Cable Protects Networks from ESD Attacks
• Copper Conductor with 24 AWG Wire Gauge

D-Link Wall Mount Enclosures specially designed for small networking, domestic applications, Audio Video, Telecom and Lab applications. Enclosures are fabricated out of CRCA steel, CNC programmed, punched, bended, welded and powder coated with highest quality standards. Configuration for standard Enclosures are: Welded frame integrated with side walls and vented top cover with fan mounting provision, rear side of the Enclosure having wall mounting provision, front glass door with lock and Key provides the visibility and security. Wall Mount Enclosures are available in 4U to 15U Variants with 400mm/450mm/500mm/ 600mm depth. Width 550mm.

• Adjustable 19” equipment mounting verticals provide the better mounting flexibility and maximizes the usable mounting space
• Depth adjustable mounting slots
• Precision engineering capabilities and best efficient software configuration product technology provides the best product quality and fastest delivery in the industry
• Top and bottom Panel with ventilation and cable entry facility
• Provision to mount the cooling fans on the top panel
• Powder coated finish with pretreatment process meeting all industry standards
• Grounding and Bonding Options. 100% assured compatibility with all equipment conforming to DIN 41494 (General industrial standard for equipment)

9V 1A Adaptor With 2.5mm DC Output Pin to maintain International Standards for Quailty Concious Customers, We offer 9V 1A Adaptor With 2.5mm DC Output Pin in wide range of input 90-275VAC

• 9V 1Amp Universal Power Adaptor for Setup box DTH
• 100V – 240V AC
• 9v – 1Amp
• O/P Pin – 2.5mm
• This is designed with high frequency switching technology which makes it highly reliable and compact in size and light in weight

SC/APC-SC/APC Single mode Simplex G657A1 Optical patch cord (LSZH) -5meters
Fiber optic patch cords and pigtails provide interconnect and cross-connect of applications over installations in entrance installations in entrance facilities, telecommunications rooms, data centers and at the desk. Patch cords support network applications in main, horizontal and equipment distribution areas and are available in riser (OFNR), and low smoke zero halogen (LSZH) rated jacket materials to comply with local cabling ordinances. Pre-terminated fiber optic pigtails support fusion splice field termination applications. Fiber optic patch cords and pigtails are available in OM4, OM3, OM2, OM1, or OS1/ OS2 fiber types to meet the demands of Gigabit Ethernet, 10 Gigabit Ethernet and high speed Fibre Channel.

• High quality zirconia ferrules
• PC radius ferrule tip
• 100% insertion loss
• Low mated pair insertion loss
• High quality nickel-plated die-cast ST nut
• Precision engineered plastic SC housings
• Wide temperature operating range
• UL-VO flammability rating on polymer materials

SC/UPC-SC/UPC Single mode Simplex G657A1 Optical patch cord (LSZH) -5meters
Fiber optic patch cords and pigtails provide interconnect and cross-connect of applications over installations in entrance installations in entrance facilities, telecommunications rooms, data centers and at the desk. Patch cords support network applications in main, horizontal and equipment distribution areas and are available in riser (OFNR), and low smoke zero halogen (LSZH) rated jacket materials to comply with local cabling ordinances. Pre-terminated fiber optic pigtails support fusion splice field termination applications. Fiber optic patch cords and pigtails are available in OM4, OM3, OM2, OM1, or OS1/ OS2 fiber types to meet the demands of Gigabit Ethernet, 10 Gigabit Ethernet and high speed Fibre Channel.

• High quality zirconia ferrules
• PC radius ferrule tip
• 100% insertion loss
• Low mated pair insertion loss
• High quality nickel-plated die-cast ST nut
• Precision engineered plastic SC housings
• Wide temperature operating range
• UL-VO flammability rating on polymer materials

SC/APC-SC/APC Single Mode Simplex G657A1 Optical Patch Cord [LHZH] 1.5 meters
Fiber optic patch cords and pigtails provide interconnect and cross-connect of applications over installations in entrance installations in entrance facilities, telecommunications rooms, data centers and at the desk. Patch cords support network applications in main, horizontal and equipment distribution areas and are available in riser (OFNR), and low smoke zero halogen (LSZH) rated jacket materials to comply with local cabling ordinances. Pre-terminated fiber optic pigtails support fusion splice field termination applications. Fiber optic patch cords and pigtails are available in OM4, OM3, OM2, OM1, or OS1/ OS2 fiber types to meet the demands of Gigabit Ethernet, 10 Gigabit Ethernet and high speed Fibre Channel.

• High quality zirconia ferrules
• PC radius ferrule tip
• 100% insertion loss
• Low mated pair insertion loss
• High quality nickel-plated die-cast ST nut
• Precision engineered plastic SC housings
• Wide temperature operating range
• UL-VO flammability rating on polymer materials

An FMS manages the fiber connections from outside of the fiber rack to the fiber routers. Fiber cable duct containing many fibers come from far end sites and terminate on FMS using splicing technology. FMS has fiber in and fiber out ports. From fiber, out port, the fiber patch will go to fiber optics-based router, Frame is modulized design with drawable trays inside and cold-rolled steel box. It could be pre-installed with various kinds of fiber optic adapters and pigtails. It is of standard size and properly designed to control the bend radius of the cable inside the enclosure to avoid extra optical loss. This frame is ideal for indoor fiber optic cables connection storage, distribution, and management
(Also available in 12,24,48,96. SC/UPC SC/APC)

• It can fix the optic cable and protect the connection between cables and pigtails.
• The box is a unique structure, reasonable layout. It's easy installation and convenient maintenance
• There is clear identification. Easy for transfer, jumper, and test

An FMS manages the fiber connections from outside of the fiber rack to the fiber routers. Fiber cable duct containing many fibers come from far end sites and terminate on FMS using splicing technology. FMS has fiber in and fiber out ports. From fiber, out port, the fiber patch will go to fiber optics-based router, Frame is modulized design with drawable trays inside and cold-rolled steel box. It could be pre-installed with various kinds of fiber optic adapters and pigtails. It is of standard size and properly designed to control the bend radius of the cable inside the enclosure to avoid extra optical loss. This frame is ideal for indoor fiber optic cables connection storage, distribution, and management
(Also available in 12,24,48,96. SC/UPC SC/APC)

• It can fix the optic cable and protect the connection between cables and pigtails.
• The box is a unique structure, reasonable layout. It's easy installation and convenient maintenance
• There is clear identification. Easy for transfer, jumper, and test

An FMS manages the fiber connections from outside of the fiber rack to the fiber routers. Fiber cable duct containing many fibers come from far end sites and terminate on FMS using splicing technology. FMS has fiber in and fiber out ports. From fiber, out port, the fiber patch will go to fiber optics-based router, Frame is modulized design with drawable trays inside and cold-rolled steel box. It could be pre-installed with various kinds of fiber optic adapters and pigtails. It is of standard size and properly designed to control the bend radius of the cable inside the enclosure to avoid extra optical loss. This frame is ideal for indoor fiber optic cables connection storage, distribution, and management
(Also available in 12,24,48,96. SC/UPC SC/APC)

• It can fix the optic cable and protect the connection between cables and pigtails.
• The box is a unique structure, reasonable layout. It's easy installation and convenient maintenance
• There is clear identification. Easy for transfer, jumper, and test

An FMS manages the fiber connections from outside of the fiber rack to the fiber routers. Fiber cable duct containing many fibers come from far end sites and terminate on FMS using splicing technology. FMS has fiber in and fiber out ports. From fiber, out port, the fiber patch will go to fiber optics based router, Frame is modulized design with drawable trays inside and cold-rolled steel box. It could be pre-installed with various kinds of fiber optic adapters and pigtails. It is of standard size and properly designed to control the bend radius of the cable inside the enclosure to avoid extra optical loss. This frame is ideal for indoor fiber optic cables connection storage, distribution, and management
(Also available in 12,24,48,96. SC/UPC SC/APC)

• It can fix the optic cable and protect the connection between cables and pigtails.
• The box is a unique structure, reasonable layout. It's easy installation and convenient maintenance
• There is clear identification. Easy for transfer, jumper, and test

An FMS manages the fiber connections from outside of the fiber rack to the fiber routers. Fiber cable duct containing many fibers come from far end sites and terminate on FMS using splicing technology. FMS has fiber in and fiber out ports. From fiber, out port, the fiber patch will go to fiber optics-based router, Frame is modulized design with drawable trays inside and cold-rolled steel box. It could be pre-installed with various kinds of fiber optic adapters and pigtails. It is of standard size and properly designed to control the bend radius of the cable inside the enclosure to avoid extra optical loss. This frame is ideal for indoor fiber optic cables connection storage, distribution, and management
(Also available in 12,24,48,96. SC/UPC SC/APC)

• It can fix the optic cable and protect the connection between cables and pigtails.
• The box is a unique structure, reasonable layout. It's easy installation and convenient maintenance
• There is clear identification. Easy for transfer, jumper, and test

2 Way PLC Tube Type Planar Light Circuit (PLC) splitters exhibit uniform signal splitting for FTTH and PON networks. It is fabricated using silica optical waveguide technology,

• 2 way PLC Tube
• Without Connector
• Quartz substrate integrated waveguard
• Good Uniformity and low insertion loss
• Low Polaration Dependent Loss
• Excellent Environmental Stability
• High Reliability
• channel-to-channel uniformity
• Small size

MODULAR Crimping tool is used for connecting cables. MX MODULAR Crimping tool will make your work safe and easy. MX MODULAR Crimping tool will easily crimp your RJ45 cable in the right manner. MX MODULAR Crimping tool is made from high quality material. MX MODULAR Crimping tool is used for cuts, crimps, & strips of RJ 45 cables

• Good quality crimping tool for IDC Connector cables
• Long handle for better grip
• Good quality material handle cover to provide you good grip while working
• Metal body
• Black-oxide finished tool 

It is Hard And Durable Enough To Crimp The Network Cables For Using Magnetic Steel.The Mouth Of The Press-Pliers Is Made Of High Quality Steel. It Won't Damage The Shelled-Wire When Crimping.The Handle Of The Crimper Is Long Enough, Which Will Help You Crimping Effortless.The Perfect Tool For Making Your Own Network Cables Rj45 And Rj11 Cables Portable Style With Perfect Shape.For Network Installations Up To 100 Mbps 10Base-T Ethernet And Token Ring. Suitable For Network Cable With Rj45 Connector And Adsl Cable With Rj11 Connect. Suitable For Cat5 And Cat5E Cable With 8P8C, 6P6C And 4P4C Plugs

• Suitable For Network Cable With Rj45 Connector And Adsl Cable With Rj11 Connect.
• Suitable For Cat5 And Cat5E Cable With 8P8C, 6P6C And 4P4C Plugs
• For Network Installations Up To 100 Mbps 10Base-T Ethernet And Token Ring.
• The Mouth Of The Press-Pliers Is Made Of High Quality Steel. It Won'T Damage The Shelled-Wire When Crimping.
• Hard And Durable Enough To Crimp The Network Cables For Using Magnetic Steel 

This fiber optics distribution box is used as a termination point for the feeder cable to connect with the drop cable in the FTTx communication network system. The fiber splicing, splitting, distribution can be done in this box, and meanwhile, it provides solid protection and management for the FTTH, FTTB, FTTX Network building (BC-FDB-1*8)

• Water-proof design for both indoor and outdoor uses
• Material: Mild Steel
• Thickness: 2-5mm
• The distribution panel can be flipped up, feeder cable can be placed in a cup-joint way, easy for maintenance and installation.

Fiber Sleeves 60mm has length: 60mm (+-0.5mm) Consist of a Rod, hot fusion tubing and cross linked Polyolefin. To rebuild the coating of fiber to provide mechnical strangth at the fusion joint area and keep the optical transmission properties. has 304 grade Stainless steel needles, Outer diameter:2.5~2.4 mm

• Moisture resistant for environmental protecion
• clear sleeve make it easy to detect splice before shrinkage.
• Easily use and avoid any damages to the oprical fiber during installation

SC/APC-SC/UPC Single mode Simplex G657A1 Optical patch cord (LSZH) -5meters
Fiber optic patch cords and pigtails provide interconnect and cross-connect of applications over installations in entrance installations in entrance facilities, telecommunications rooms, data centers and at the desk. Patch cords support network applications in main, horizontal and equipment distribution areas and are available in riser (OFNR), and low smoke zero halogen (LSZH) rated jacket materials to comply with local cabling ordinances. Pre-terminated fiber optic pigtails support fusion splice field termination applications. Fiber optic patch cords and pigtails are available in OM4, OM3, OM2, OM1, or OS1/ OS2 fiber types to meet the demands of Gigabit Ethernet, 10 Gigabit Ethernet and high speed Fibre Channel.

• High quality zirconia ferrules
• PC radius ferrule tip
• 100% insertion loss
• Low mated pair insertion loss
• High quality nickel-plated die-cast ST nut
• Precision engineered plastic SC housings
• Wide temperature operating range
• UL-VO flammability rating on polymer materials

Complete Connect’s SFP+ 10G direct attach copper (DAC) cable assemblies offer customers high performance, cost effective I/O solutions for 10G Ethernet and 10G Fibre Channel applications.
DAC SFP+ to SFP+ cables offer the lowest cost connectivity for 10GBASE-CR as well as a high port density and low power requirement. For short distances DAC cables offer a lower cost alternative to SFP+ Transceivers and fibre patch cables.
There are 2 versions of SFP+ direct attach copper cable; passive and active. Passive DAC cables enable connection up to 7m.
Active DAC cables have an increased distance up to 15m and also have a reduced size cable diameter. Note – some equipment brands will only accept active DAC cables.

•  SFP+ to SFP+ Connector  
•  Copper Passive
•  1 Meter
•  AWG24
•  Compliant to SFP MSA
•  Low power consumption
•  Excellent EMI performance
•  High reliability
•  RoHS Compliant
•  Wide operating temperature range:
•  Standard: 0°C to +70°C
•  Industrial: -40°C to +85°C

Complete Connect’s SFP+ 10G direct attach copper (DAC) cable assemblies offer customers high performance, cost effective I/O solutions for 10G Ethernet and 10G Fibre Channel applications.
DAC SFP+ to SFP+ cables offer the lowest cost connectivity for 10GBASE-CR as well as a high port density and low power requirement. For short distances DAC cables offer a lower cost alternative to SFP+ Transceivers and fibre patch cables.
There are 2 versions of SFP+ direct attach copper cable; passive and active. Passive DAC cables enable connection up to 7m.
Active DAC cables have an increased distance up to 15m and also have a reduced size cable diameter. Note – some equipment brands will only accept active DAC cables.

• SFP+ to SFP+ Connector  
•  Copper Passive
•  3 Meter
•  AWG24
•  Compliant to SFP MSA
•  Low power consumption
•  Excellent EMI performance
•  High reliability
•  RoHS Compliant
•  Wide operating temperature range:
•  Standard: 0°C to +70°C
•  Industrial: -40°C to +85°

Complete Connect’s SFP+ 10G direct attach copper (DAC) cable assemblies offer customers high performance, cost effective I/O solutions for 10G Ethernet and 10G Fibre Channel applications.
DAC SFP+ to SFP+ cables offer the lowest cost connectivity for 10GBASE-CR as well as a high port density and low power requirement. For short distances DAC cables offer a lower cost alternative to SFP+ Transceivers and fibre patch cables.
There are 2 versions of SFP+ direct attach copper cable; passive and active. Passive DAC cables enable connection up to 7m.
Active DAC cables have an increased distance up to 15m and also have a reduced size cable diameter. Note – some equipment brands will only accept active DAC cables.

• SFP+ to SFP+ Connector  
•  Copper Passive
•  5 Meter
•  AWG24
•  Compliant to SFP MSA
•  Low power consumption
•  Excellent EMI performance
•  High reliability
•  RoHS Compliant
•  Wide operating temperature range:
•  Standard: 0°C to +70°C
•  Industrial: -40°C to +85°C

Complete Connect’s SFP+ 40G direct attach copper (DAC) cable assemblies offer customers high performance, cost effective I/O solutions for 40G Ethernet and 40G Fibre Channel applications.
DAC SFP+ to SFP+ cables offer the lowest cost connectivity for 40GBASE-CR as well as a high port density and low power requirement. For short distances DAC cables offer a lower cost alternative to SFP+ Transceivers and fibre patch cables.
There are 2 versions of SFP+ direct attach copper cable; passive and active. Passive DAC cables enable connection up to 7m.
Active DAC cables have an increased distance up to 15m and also have a reduced size cable diameter. Note – some equipment brands will only accept active DAC cables.

• SFP+ to SFP+ Connector  
•  Copper Passive
•  1 Meter
•  AWG24
•  Compliant to SFP MSA
•  Low power consumption
•  Excellent EMI performance
•  High reliability
•  RoHS Compliant
•  Wide operating temperature range:
•  Standard: 0°C to +70°C
•  Industrial: -40°C to +85°C

Complete Connect’s SFP+ 40G direct attach copper (DAC) cable assemblies offer customers high performance, cost effective I/O solutions for 40G Ethernet and 40G Fibre Channel applications.
DAC SFP+ to SFP+ cables offer the lowest cost connectivity for 40GBASE-CR as well as a high port density and low power requirement. For short distances DAC cables offer a lower cost alternative to SFP+ Transceivers and fibre patch cables.
There are 2 versions of SFP+ direct attach copper cable; passive and active. Passive DAC cables enable connection up to 7m.
Active DAC cables have an increased distance up to 15m and also have a reduced size cable diameter. Note – some equipment brands will only accept active DAC cables.

• SFP+ to SFP+ Connector  
•  Copper Passive
•  3 Meter
•  AWG24
•  Compliant to SFP MSA
•  Low power consumption
•  Excellent EMI performance
•  High reliability
•  RoHS Compliant
•  Wide operating temperature range:
•  Standard: 0°C to +70°C
•  Industrial: -40°C to +85°C

The RocketM Titanium is the most powerful airMAX BaseStation to date. It features 802.3af compliant PoE (Power over Ethernet), gigabit Ethernet, a GPS receiver, advanced RF shielding, and a faster processor that can provide up to a 20% increase in performance. 
The RocketM Titanium features enhanced radio performance and superior durability. Its carrier? class capabilities link distances up to 50+ km and provide breakthrough speeds of up to 150+ Mbps. The RocketM Titanium takes advantage of its Gigabit Ethernet connection to deliver high throughput for reliable data transfers. The RocketM Titanium enclosure was specifically designed to improve performance in harsh RF environments and in extreme weather conditions. Enclosed in aircraft-grade aluminum, the RocketM Titanium is a rugged, high-power, linear 2x2 MIMO radio
airMAX Technology

• GPS Synchronization: RocketM2 Titanium has integrated Ubiquiti airSync™ technology.
• 2x2 MIMO: Hi-power, linear 2x2 MIMO radios with enhanced receiver performance.
• Power supply: 802.3af compliant PoE 110-240VAC 48VDC 0.5A
• US power cord, US/FCC channel/frequency plan only

USG-PRO-4 Enterprise Gateway Router withUSG-PRO-4 Enterprise Gateway Router with four Gigabit Ethernet ports and two SFP combination ports, 2 Combination SFP/RJ-45 Ports from Ubiquiti Networks is designed to be the backbone of a network. This gateway is designed to support multiple network switches which in turn can support a variety of networked devices such as access points, management stations, VoIP devices, and much more. The integrated SFP combination ports make it simple to connect fiber channel devices such as SAN servers and other local area networked devices. On the back of this rack mountable gateway, you will find a single RJ-45 serial console port for command-line interface management, two LAN ports, two WAN ports, and two SFP combination ports offering a diverse set of connection options.

• Dual-Core 1 GHz Processor
• 2 GB On-Board Flash Memory
• Rackmountable Design
• 1 x RJ-45 Serial Console Port

AC10 leads the way in next-generation routers, offering dual-band Gigabit wireless with all-new 802.11ac Wave 2.0 Wi-Fi. Its powerful 1GHz CPU and 128MB DDR3 provide the best performance in both 2.4GHz and 5GHz. The 5GHz band works at up to 867Mbps, while the 2.4GHz frequency tops 300Mbps, serving an incredible combined bandwidth of 1167Mbps.
Compliant with the next generation 802.11ac wave 2.0 WiFi standard, AC10 provides a dual-band wireless speed of as high as 1167 Mbps, 3 times faster than the wireless 11N speed, ensuring stable online gaming and 4K streaming on YouTube and Netflix. Equipped with built-in high-powered amplifiers, external antennas, gigabit Ethernet ports, MU-MIMO and Beamforming+ technology, AC10 offers a great operating range for wide WiFi coverage so that you will never worry about too many devices to connect, and also enables you to have the best internet experience. Additionally, Tenda WiFi app allows you to manage your network anywhere anytime to live a smart and easy life.

• AC1200 Mbps Wireless
• MU-MIMO
• 3 Gigabit LAN & 1 Gigabit WAN
• 1GHz CPU ??? VPN Client and Server
• Dual-Band Wireless
• 4 Omni-directional Antennas
• Parental Controls
• WiFi Schedule

D-Link Wall Mount Enclosures specially designed for small networking, domestic applications, Audio Video, Telecom and Lab applications. Enclosures are fabricated out of CRCA steel, CNC programmed, punched, bended, welded and powder coated with highest quality standards. Configuration for standard Enclosures are: Welded frame integrated with side walls and vented top cover with fan mounting provision, rear side of the Enclosure having wall mounting provision, front glass door with lock and Key provides the visibility and security. Wall Mount Enclosures are available in 4U to 15U Variants with 400mm/450mm/500mm/ 600mm depth. Width 550mm.

• Adjustable 19” equipment mounting verticals provide the better mounting flexibility and maximizes the usable mounting space
• Depth adjustable mounting slots
• Precision engineering capabilities and best efficient software configuration product technology provides the best product quality and fastest delivery in the industry
• Top and bottom Panel with ventilation and cable entry facility
• Provision to mount the cooling fans on the top panel
• Powder coated finish with pretreatment process meeting all industry standards
• Grounding and Bonding Options. 100% assured compatibility with all equipment conforming to DIN 41494 (General industrial standard for equipm

D-Link Wall Mount Enclosures specially designed for small networking, domestic applications, Audio Video, Telecom and Lab applications. Enclosures are fabricated out of CRCA steel, CNC programmed, punched, bended, welded and powder coated with highest quality standards. Configuration for standard Enclosures are: Welded frame integrated with side walls and vented top cover with fan mounting provision, rear side of the Enclosure having wall mounting provision, front glass door with lock and Key provides the visibility and security. Wall Mount Enclosures are available in 4U to 15U Variants with 400mm/450mm/500mm/ 600mm depth. Width 550mm.

• Adjustable 19” equipment mounting verticals provide the better mounting flexibility and maximizes the usable mounting space
• Depth adjustable mounting slots
• Precision engineering capabilities and best efficient software configuration product technology provides the best product quality and fastest delivery in the industry
• Top and bottom Panel with ventilation and cable entry facility
• Provision to mount the cooling fans on the top panel
• Powder coated finish with pretreatment process meeting all industry standards
• Grounding and Bonding Options. 100% assured compatibility with all equipment conforming to DIN 41494 (General industrial standard for equipment)

G/EPON 1GE Safe ONU is support Dual mode(EPON and GPON), It can also be applied to a wide temperature environment, and also has a powerful firewall function. G/EPON 1GE ONU meets telecom operators FTTO (office), FTTD (Desk), FTTH(Home) broadband speed, SOHO broadband access, video surveillance and other requirements and design a GPON/EPON Gigabit Ethernet products. The box is based on the mature Gigabit GPON/EPON technology, highly reliable and easy to maintain, with guaranteed QOS for different service. And it is fully compliant with technical regulations such as ITU-T G.984.x and IEEE802.3ah.

• 1 G/EPON port(EPON PX20+ and GPON Class B+)
• Wavelength:Tx1310nm,Rx 1490nm
• SC/UPC connector

FIber stripper is a unique tool specially designed for stripping 250 µm.Buffer coating from 125 µm glass optical fiber 

• V-Opening in blade allow for accurate buffer coating removal
• Factory set requires no adjustment.
• Prevents scratching or nicking on optical fiber.
• Durable and easy to use

The RD-5G30-LW features the same gain as the RD-5G30 and adds the following advantages
Lightweight yet robust components lessen the load.
The extended depth of the dish reflector rejects noise interference in co-location deployments.
The design of the mounting bracket allows for ease of installation on a pole or tower

• Optional Alignment Accessory
• Optional Isolator Radome
• Innovative Industrial Design
• Plug and Play Integration

Ratio Couplers are an all fiber, polished directional coupler with variable coupling ratio. These devices can be used to divide or combine optical signals in fiber optics research. Available wavelengths include 630 nm, 830 nm, 980 nm, 1060 nm, 1300 nm, and 1550 nm.

• Very precise coupling ratio adjustment — from 0–100%
• Low insertion loss
• High polarization isolation
• PM and non-PM types available